Seat Alhambra Key Problems
Seat's jumbo MPV range is among the best in its class when it comes to resale value. And with a new model on sale, it's better than ever.
There are many reasons why the key fob won't work properly, including an unresponsive coin battery or water damage to the receiver module or signal interference. This article will walk you through the steps to get it back in working order.
Water Damage
If your key fob for the seat alhambra can withstand the wash cycle or a dip in an ocean or a pool then it's got a waterproof chip. But be careful not to do this often, as prolonged exposure to water increases the chance of the key fob becoming damaged. If your key fob ceases to functioning after being exposed to rain or clean tap water, unplug the battery and wipe the electronic component using a paper towel. Dry it completely before replacing the battery. In the event of exposure to soapy or salty water, it is recommended to wash the chip with isopropyl alcohol or an electronic cleaner before attempting to put the battery back in.
Faulty Receiver Module
If the key fob does not lock or unlock even after you've replaced the battery in the button cell It is possible that the receiver module has an issue. The good news is that it is a relatively simple and cost-effective fix. You can simply disconnect the 12 volt battery for several minutes (first remove the negative cable, then press the horn button several times) to remove any remaining electric current, then reconnect it in reverse order e.g. Positive first, then negative.
ESP Warning Light – If the ESP symbol blinks, it is normal. www.g28carkeys.co.uk means that you are driving over terrain that has poor traction. This could be due to gravel, snow or surface water. If the ESP light is constantly flashing, it is a sign there is a problem with the system. This can be identified by using an iCarsoft i908 seat OBD code reader kit. It will provide the full description of the problem.
Dead Coin Battery
A dead battery for the coin is among the most frequent causes for the keys for the seat to stop working. The key fob is powered by a small button-cell battery. It is recommended to replace it with a brand new one with the same size, voltage, and specification as the original. When replacing the battery on the key fob, remove the metal clips and make sure that the contacts on the key fob are in good condition and free of corrosion.
If the key fob was exposed to water (such as soapy or rain tap water) it is recommended that you remove and clean the chip using an electronic cleaner or isopropylethanol before installing a brand new battery. The chip may be permanently damaged by water. If the key fob still not working after replacing the battery, it could be necessary to replace the entire key fob.
Faulty Receiver Module
If your key fob has stopped working after replacing the battery and it didn't help, or if it stopped working completely out of the blue The receiver module may have developed a fault. The receiver module is responsible for capturing the radio frequency signals that are sent by the remote key fob and changing them into electrical signals that are then utilized by other modules in the car.
If the receiver module has developed a fault it will not respond to any of the commands issued by your remote key fob. In this case you'll need to go to a dealer for reprogramming your key fob and new receiver module.
The key fob comes with rubber seals that block water from getting into the chip inside. However, if you submerge the key fob in soapy water or salty ocean water, the chips inside may be damaged. You can attempt to clean the chip by rub it with isopropyl alcohol or electronic cleaner, however should your key fob does not work after this, you'll have to purchase a replacement.
If the keys are in a pair but the receiver module has developed a fault you can try rebooting all the on-board electronics by disconnecting the battery at 12 volts for a short period of time. Connect the battery in reverse (negative cable to positive first). This will reset the onboard electronic circuits and restore their functionality.
Faulty Electronic Chip
The key fob is outfitted with a chip that transmits a signal from the key to the receiver module every time the key is used. If the signal isn't in line with the one the car has stored, the immobilizer will disable and stop the car from starting. If the key fob won't function and you are not able to reprogram it, it could be because of an incompatible microchip.
The chip in the key fob may need change to allow it to function again. The best way to do this is to remove the key from its housing and then using a pin needle to get into contact with each of the retaining clips made of steel. If they are corroded or damaged, you'll have to replace them to allow the remote control to function. Make sure that the replacement batteries are of the same size, voltage, and specification as the original.
The Seat Alhambra is a well-designed and popular model but like any other car it is not without its challenges. issues with specific components or equipment. Some owners have reported problems with the auto climate control system. It may malfunction and be stuck in a specific setting. In the same way, the infotainment system has also been known to malfunction and freeze screens.